Kia Rio Manuals

Kia Rio: Multimedia Jack Troubleshooting - Audio - Body Electrical System - Kia Rio UB 2012-2024 Service ManualKia Rio: Multimedia Jack Troubleshooting

Symptom
 Suspected area
 Repairment
Pressing power switch does not turn on system
 Radio receiver power source circuit
 R-1
LCD module
 R-1
Panel switch does not function
 Steering pad switch circuit
 R-3
Audio H/U front pcb ass'y
 R-1
Radio receiver power source circuit
 R-1
No sound can be heard from speakers
 Radio receiver power source circuit
 R-1
Speaker ↔ H/U wiring
 R-4
Speaker input Waveform
 R-5
Noise occurs
 Proceed to "noise occurs"
 R-7
Radio broadcast cannot be received
Proceed to "radio broadcast cannot be received (poor reception)"
 R-6
Disc cannot be inserted or is ejected right after insertion
 Radio receiver power source circuit
 R-1
Proceed to "Disc cannot be inserted or is ejected right after insertion"
 R-12
Disc cannot be ejected.
 Radio receiver power source circuit
 R-1
CD sound skips
 CD player
 R-13
Illumination for radio receiver does not come on whth light
control switch on.
 Illumination circuit
R-8
Head unit display
 R-8
Radio receiver power source circuit
 R-1
Display does not dim with light control switch turned on
 Illumination circuit
R-9
Power does not turn off
 Audio H/U
 R-1
Bluetooth voice recognition faulty
 Audio H/U
 R-1
Mic input
 R-10
USB I/F error
 Audio H/U
 R-1
Usb device faulty
 R-11
Multimedia terminal connection
 R-10
iPod I/F error
 Audio H/U
 R-1
Ipod faulty
 R-11
Multimedia terminal connection
 R-10
AUX connection error
 Audio H/U
 R-1
Multimedia terminal connection
 R-10

R-1 : Replace the audio head unit
1.
Check the same problems after replaceing the audio head unit
OK
 ▶ If Audio is normal operating, replace the audio head unit
NG
 ▶ Check the vehicle wiring. (Refer to removal procedure. R-2)

R-2 : Check the power connection of audio head unit.
1.
Remove the audio head unit.
2.
Check the specified condition of terminal.


OK
Tester Connection
 Condition
 Specified Condition
CON-B11 ↔ GND
 Always
 9~12 V
CON-B12 ↔ GND
 Always
 9~12 V
CON-B24 ↔ GND
 Always
 Below 1Ω

NG
 ▶ Check again after repairing or replacing the Cable harness or Connector.

R-3 : Check the steering wheel remote control
1.
Check the steering wheel remote control connector specification (Refer to "Audio remote control - inspection")
OK
 ▶ Replace the audio head unit. (Refer to R-1)
NG
 ▶ Replace the steering wheel remote control switch.

R-4 : Check the wiring harness and connector
1.
Remove the audio head unit
OK
 ▶ FOR PA30A, BA900


Tester Connection
 Condition
 Specified Condition
CON-A1 ↔ RL SPK +
 Always
 Below 1Ω
CON-A10 ↔RL SPK -
 Always
 Below 1Ω
CON-A2 ↔ FL SPK +
 Always
 Below 1Ω
CON-A11 ↔ FL SPK -
 Always
 Below 1Ω
CONA3 ↔ FR SPK +
 Always
 Below 1Ω
CON-A12 ↔ FR SPK -
 Always
 Below 1Ω
CON-A4 ↔ RR SPK +
 Always
 Below 1Ω
CON-A13 ↔ RR SPK -
 Always
 Below 1Ω
CON-A1, 2, 3, 4, 10, 11, 12, 13 ↔ GND
 Always
 OPEN

R-5 : Check the wiring harness and connector
1.
Remove the audio head unit
2.
Check the output of audio head unit and external amplifier using the oscilloscope
OK
 ▶ FOR PA30A, BA900


Tester Connection
 Condition
 Specified Condition
CON-A1 ↔ GND
 Audio sound is being produced
 A waveform synchronized with sound is output
CON-A10 ↔ GND
 Audio sound is being produced
 A waveform synchronized with sound is output
CON-A2 ↔ GND
 Audio sound is being produced
 A waveform synchronized with sound is output
CON-A11 ↔ GND
 Audio sound is being produced
 A waveform synchronized with sound is output
CON-A3 ↔ GND
 Audio sound is being produced
 A waveform synchronized with sound is output
CON-A12 ↔ GND
 Audio sound is being produced
 A waveform synchronized with sound is output
CON-A4 ↔ GND
 Audio sound is being produced
 A waveform synchronized with sound is output
CON-A13 ↔ GND
 Audio sound is being produced
 A waveform synchronized with sound is output

R-6 : Radio Broadcast cannot be Received (Bad reception)
1.
Check the radio broadcast reception after replacing the audio head unit
OK
 ▶ If Audio is normal operating, replace the audio head unit

NG
 ▶ Go to step 2

2.
Check the antenna jack
NG
 ▶ Check again the radio broadcast reception after connecting the antenna jack

OK
 ▶ Go to step 3

3.
Check the antenna amp input voltage (Refer to "Antenna - Glass antenna circuit inspection"
NG
 ▶ Check the antenna amp input voltage (Refer to "Antenna - Antenna cable"

OK
 ▶ Go to step 4

4.
Check the feeder cable connection (Refer to "Antenna - Antenna cable")
NG
 ▶ Check again after repairing or replacing the antenna feeder cable.

OK
 ▶ Go to step 5

5.
Check again the radio broadcast reception after replacing the external amplifier
OK
 ▶ If Audio is normal operating, replace the external amplifier

NG
 ▶ Go to step 6

6.
Check and repair the glass antenna. (Refer to "Antenna - Glass antenna test")
R-7 : Check that speakers are installed tightly.
NG
 ▶ Install the speakers tightly.

OK
 ▶ Go to step 1

1.
Noise source description
Condition in Which Noise Occurs
 Noise Type
Depressing accelerator pedal increases noise, and stopping engine stops noise immediately
 Generator nosie
When A/C or heater is operating
 Blower motor noise
•
When rapidly accelerating on unpaved road
•
When engine switch is turned on (IG)
Fuel pump noise
•
When horn switch is pressed and released
•
When horn switch is pressed and held down
Horn noise
Running engine causes soft noise, and stopping engine stops noise immediately
 Ignition noise
Noise occurs synchronously with turn signal flash
 Flasher noise
Noise occurs during window washer operation
 Washer noise
Running engine causes noise, but stopping engine does not stop noise
 Engine coolant temperature sensor noise
When wiper is operating
 Wiper noise
When brake pedal is depressed
 Stop light switch noise
Other
 Static electricity on vehicle

OK
 ▶ Check the noise source

NG
 ▶ Check again after replacing the audio head unit

2.
Repair or replace the noise source
R-8 : Check again after replacing the audio head unit


OK
 ▶ Remove the audio head unit

NG
 ▶ Go to step 1

1.
Check the input signal of Illumination (+)
FOR PA30A
Tester Connection
 Condition
 Specified Condition
CON-A8 ↔ GND
 Always
 9~16 V

FOR BA900
Tester Connection
 Condition
 Specified Condition
CON-C5 ↔ GND
 Always
 9~16 V
CON-C4 ↔ GND
 Always
 Below 1Ω

NG
 ▶ Check the vehicle wiring

OK
 ▶ Go to step 2

2.
Check the illumination (-) input signal using the oscilloscope
FOR PA30A
Tester Connection
 Condition
 Specified Condition
CON-A17 ↔ GND
 Always
 Check the PWM waveform

FOR BA900
Tester Connection
 Condition
 Specified Condition
CON-A17/H17 ↔ GND
 Always
 Check the PWM waveform

NG
 ▶ Check the vehicle wiring and cluster PWM output.

OK
 ▶ Go to step 3

3.
Check the vehicle illumination control unit.
R-9 : Test after replacing the audio head unit
OK
 ▶ Replace the audio head unit

NG
 ▶ Go to step 1

1.
Check the illumination (-) input signal using the oscilloscope
FOR PA30A
Tester Connection
 Condition
 Specified Condition
CON-A17 ↔ GND
 Always
 Check the PWM waveform

FOR BA900
Tester Connection
 Condition
 Specified Condition
CON-A17/H17 ↔ GND
 Always
 Check the PWM waveform

Is PWM output waveform changed according to vehicle illumination control ?
NG
 ▶ Check the vehicle wiring and cluster PWM output module.

OK
 ▶ Go to step 2

2.
Check the illumination detent input signal.
FOR PA30A, BA900
Tester Connection
 Condition
 Specified Condition
CON-A9 ↔ GND
 Always
 LOW : DETENT OFF

NG
 ▶ Check the vehicle wiring and cluster DETENT output signal

Multimedia Jack Installation
1. Install the multimedia jack. 2. Connect the multimedia jack connector.    ...

See also:

Compressor Inspection
1. Check the plated parts of the disc & hub assembly (A) for color changes, peeling or other damage. If there is damage, replace the clutch set. ...

System Block Diagram
...

Positive Crankcase Ventilation (PCV) Valve: Inspection
1. Insert a thin stick (A) into the PCV valve (B) from the threaded side to check that the plunger movement.    ...

Categories


Copyright © www.kirmanual.com 2014-2024