Kia Rio: Troubleshooting
| Problem Symptoms Table |
Before replacing or repairing air conditioning components, first determine
if the malfunction is due to the refrigerant charge, air flow or compressor.
Use the table below to help you find the cause of the problem. The numbers
indicate the priority of the likely cause of the problem. Check each part in
order. If necessary, replace these parts.
After correcting the malfunction, check the complete system to ensure
that performance is satisfactory.
| Symptom |
Suspect Area |
| No blower operation |
1. Blower fuse |
| 2. Blower relay |
|
| 3. Blower motor |
|
| 4. Blower resistor, Power mosfet or PWM blower module |
|
| 5. Blower speed control switch or knob |
|
| 6. Wire harness |
|
| No air temperature control |
1. Engine coolant capacity |
| 2. Heater control assembly |
|
| 3. Temperature control actuator or cable |
|
| No compressor operation |
1. Refrigerant capacity |
| 2. A/C Fuse |
|
| 3. Compressor |
|
| 4. A/C pressure transducer |
|
| 5. A/C switch |
|
| 6. Evaporator temperature sensor |
|
| 7. Wire harness |
|
| 8. High CAN |
|
| No cool comes out |
1. Refrigerant capacity |
| 2. Refrigerant pressure |
|
| 3. Drive belt |
|
| 4. Compressor |
|
| 5. A/C pressure transducer |
|
| 6. Evaporator temperature sensor |
|
| 7. A/C switch |
|
| 8. Heater control assembly |
|
| 9. Wire harness |
|
| 10. High CAN |
|
| 11. Temperature control actuator or cable |
|
| Insufficient cooling |
1. Refrigerant capacity |
| 2. Drive belt |
|
| 3. Compressor |
|
| 4. Condenser |
|
| 5. Expansion valve |
|
| 6. Evaporator |
|
| 7. Refrigerant lines |
|
| 8. A/C pressure transducer |
|
| 9. Heater control assembly |
|
| 10. High CAN |
|
| No engine idle-up when A/C switch ON |
1. Engine ECM |
| 2. Wire harness |
|
| No air inlet control |
1. Heater control assembly |
| 2. Intake actuator |
|
| No mode control |
1. Heater control assembly |
| 2. Mode control actuator or cable |
|
| No cooling fan operation |
1. Cooling fan fuse |
| 2. Fan motor |
|
| 3. Blower resistor, Power mosfet or PWM blower module |
|
| 4. Engine ECM |
|
| 5. Wire harness |
Specification
Air Conditioner
Item
Specification
Compressor
Type
DVE12 (Externally Controlled Variable Swash Plate Type)
Oil type & Capacity
PAG ...
Special Service Tools
Tool (Number and name)
Illustration
Use
09977-25100
Disc & hub assembly bolt remover
Removal and installation of disc & hub assembly ...
See also:
Description
Manifold Absolute Pressure Sensor (MAPS) is a speed-density type sensor
and is installed on the surge tank. It senses absolute pressure of the surge
tank and transfers the analog signal propo ...
ESC OFF Switch Description
1.
The ESC OFF switch is for the user to turn off the ESC system.
2.
The ESC OFF lamp is on when ESC OFF switch is engaged.
...
Installation
1.
Dowel pin of crankshaft setted about 3° with vertical center line.
2.
Align the TDC marks (A) of the CVVT sprockets with the upper su ...
Copyright © www.kirmanual.com 2014-2024