Kia Rio Manuals

Kia Rio: Steering Column and Shaft Replacement - Electric Power Steering - Steering System - Kia Rio UB 2012-2024 Service ManualKia Rio: Steering Column and Shaft Replacement

1.
Disconnect the battery negative cable from the battery and then wait for at least 30 seconds.
2.
Turn the steering wheel so that the front wheels can face straight ahead.
3.
Remove the airbag module.
(Refer to RT group - "Air Bag Module")
4.
Loosen the lock nut (A), disconnect the connector (B) and then remove the steering wheel by using SST(0956-11001).
Tightening torque :
39.2 ~ 44.1N.m(4.0 ~ 4.5kgf.m, 28.9 ~ 32.5lb-ft)




     
Do not hammer on the steering wheel to remove it; it may damage the steering column.
5.
Loosen the screw and then remove the steering column upper (A) and lower shroud (B).
6.
Disconnect the connector (B) and then remove the clock spring (A).



     
• When assembling set the center position by setting the marks between the clock spring and the cover into line. Make an array the mark (▶◀) by turning the clock spring clockwise to the stop and then 2.0 revolutions counterclockwise.
7.
Disconnect the connector (A).
8.
Loosen the screw and then remove the multifunction switches (A).
9.
Remove the crash pad side cover, Fuse box cover and lower crash pad.
(Refer to BD group - "Interior / Crash Pad")
10.
Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of the steering gear box.
Tightening torque :
32.4 ~ 37.3N.m(3.3 ~ 3.8kgf.m, 23.9 ~ 27.5lb-ft)



     
•
Lock the steering wheel in the straight ahead position to prevent the damage of the clock spring inner cable when you handle the steering wheel.
•
Do not use the bolt again.
11.
Disconnect all connectors connected the steering column & EPS unit assembly.
12.
Remove the steering column & EPS unit assembly by loosening the mounting bolt (B) and nuts (A).
Tightening torque :
Nut : 14.7 ~ 17.7N.m(1.5 ~ 1.8kgf.m, 10.8 ~ 13.0lb-ft)
Bolt : 44.1 ~ 49.0N.m(4.5 ~ 5.0kgf.m, 32.5 ~ 36.2lb-ft)



13.
Installation is the reverse of the removal.

     
If MDPS type, you must be EPS type recognition
(Refer to ST group - E.P.S/repair procedures)
14.
Compensate the steering angle sensor after replaceing the steering column.
Description
- EPS (Electronic Power Steering, Column assist type) system uses an electric motor to assist the steering force and it is an engine operation independent steering system ...

Steering Column and Shaft Disassembly
Key lock assembly 1. Make a groove on the head of special bolts (A) with a chisel. 2. Loosen the special bolt using a screw driver a ...

See also:

Rear Coil Spring Replacement
1. Remove the rear wheel & tire. (Both RH side and LH side) Tightening torque : 88.3 ~ 107.9N.m(9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb ...

Removal
1. Turn the ignition switch OFF and disconnect the battery negative (-) cable. 2. Remove the intake manifold (Refer to “Intake And Exhaust ...

Description
Continuous Variable Valve Timing (CVVT) system advances or retards the valve timing of the intake and exhaust valve in accordance with the ECM control signal which is calculated by the engine ...

Categories


Copyright © www.kirmanual.com 2014-2024