Kia Rio: Interior Trim Replacement
Door Scuff Trim Replacement
| •
|
Put on gloves to protect your hands.
|
| •
|
Use a plastic panel removal tool to remove interior trim
pieces to without marring the surface.
|
| •
|
Take care not to bend or scratch the trim and panels.
|
|
|
1. |
Using a screwdriver or remover, remove the front door scuff trim
(A).
[Front]
|
|
2. |
Remove the rear seat cushion.
(Refer to the BD group - "Rear Seat")
|
|
3. |
After loosening the mounting screws, then remove the rear door
scuff trim (A).
[Rear]
|
|
4. |
Installation is the reverse of removal.
|
• |
Replace any damage clips.
|
|
|
Cowl Side Trim Replacement
| •
|
Put on gloves to protect your hands.
|
| •
|
Use a plastic panel removal tool to remove interior trim
pieces to without marring the surface.
|
| •
|
Take care not to bend or scratch the trim and panels.
|
|
|
1. |
Remove the front door scuff trim.
|
|
2. |
Remove the hood release handle.
(Refer to the BD group – “Hood”)
|
|
3. |
Using a screwdriver or remover, remove the cowl side trim (A).
|
|
4. |
Installation is the reverse of removal.
|
• |
Replace any damage clips.
|
|
|
Front Pillar Trim Replacement
| •
|
Put on gloves to protect your hands.
|
| •
|
Use a plastic panel removal tool to remove interior trim
pieces to without marring the surface.
|
| •
|
Take care not to bend or scratch the trim and panels.
|
|
|
1. |
Using a screwdriver or remover, remove the front pillar trim (A).
|
• |
Lock pin (B) is need to changed to new product
surely.
|
|
|
|
2. |
Disconnect the tweeter speaker connector (A).
|
|
3. |
Installation is the reverse of removal.
|
• |
Replace any damage clips.
|
|
• |
Make sure the connector is connected properly.
|
|
|
Center Pillar Trim Replacement
| •
|
Put on gloves to protect your hands.
|
| •
|
Use a plastic panel removal tool to remove interior trim
pieces to without marring the surface.
|
| •
|
Take care not to bend or scratch the trim and panels.
|
|
|
1. |
Remove the following items :
|
|
2. |
Disconnect the battery negative cable, and wait for at least three
minutes before beginning work.
|
|
3. |
The seat belt anchor pretensioner (A) can be removed after pushing
the lock pin (B) as arrow direction.
|
|
4. |
Using a screwdriver or remover, remove the center pillar lower
trim (A).
|
|
5. |
Using a screwdriver or remover, remove the center pillar upper
trim (A).
|
|
6. |
Installation is the reverse of removal.
|
• |
Replace any damage clips.
|
|
|
Rear Pillar Trim Replacement
| •
|
Put on gloves to protect your hands.
|
| •
|
Use a plastic panel removal tool to remove interior trim
pieces to without marring the surface.
|
| •
|
Take care not to bend or scratch the trim and panels.
|
|
|
1. |
Remove the following items :
| A. |
Rear seat assembly
(Refer to the BD group - "Rear Seat")
|
|
|
2. |
After loosening the mounting screws, then remove the rear door
scuff trim (A).
|
|
3. |
Using a screwdriver or remover, remove the rear transverse trim
(A).
|
|
4. |
After loosening the mounting bolt, then remove the rear seat belt
lower anchor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
5. |
After loosening the mounting blots, then remove the rear seat
bracket (A).
|
|
6. |
Using a screwdriver or remover, remove the lamp (A).
|
|
7. |
Disconnect the lamp connector (B).
|
|
8. |
After loosening the mounting screws, then remove the luggage side
trim (A).
|
|
9. |
Remove the rear seat belt upper anchor cover (B).
|
|
10. |
Using a screwdriver or remover, remove the rear pillar trim (A).
|
|
11. |
Installation is the reverse of removal.
|
• |
Make sure the connectors are connected in properly.
|
|
• |
Replace any damage clips.
|
|
|
| •
|
Put on gloves to protect your hands.
|
| •
|
Use a plastic panel removal tool to remove interior trim
pieces to without marring the surface.
|
| •
|
Take care not to bend or scratch the trim and panels.
|
|
|
1. |
Using a screwdriver or remover, remove the rear pillar trim (A).
|
|
2. |
Installation is the reverse of removal.
|
• |
Replace any damage clips.
|
|
|
Luggage Side Trim Replacement
| •
|
Put on gloves to protect your hands.
|
| •
|
Use a plastic panel removal tool to remove interior trim
pieces to without marring the surface.
|
| •
|
Take care not to bend or scratch the trim and panels.
|
|
|
1. |
Remove the rear seat.
(Refer to the BD group – “Rear Seat”)
|
|
2. |
Remove the rear door scuff trim.
|
|
3. |
Remove the rear transverse trim.
|
|
4. |
After loosening the mounting screws, then remove the luggage side
trim.
|
|
5. |
Installation is the reverse of removal.
|
• |
Replace any damage clips.
|
|
|
1 . Luggage side trim [LH]
2 . Luggage side trim [RH]
3 . Rear transverse trim
4 . Luggage floor box trim
|
5 . Luggage covering complete assembly (1)
6 . Covering shelf side damper
7 . Luggage tray
8 . Luggage covering complete assembly (2)
|
Rear Package Tray Trim Replacement
| •
|
Put on gloves to protect your hands.
|
| •
|
Use a plastic panel removal tool to remove interior trim
pieces to without marring the surface.
|
| •
|
Take care not to bend or scratch the trim and panels.
|
|
|
1. |
Remove the rear seat assembly.
(Refer to the BD group – “Rear Seat”)
|
|
2. |
Using a screwdriver or remover, remove the rear pillar trim (A).
|
|
3. |
After loosening the mounting screws, then remove the rear door
scuff trim (A).
|
|
4. |
After loosening the mounting bolt, then remove the rear seat belt
lower anchor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
5. |
After loosening the mounting blots, then remove the rear seat
folding bracket (A).
|
|
6. |
After loosening the mounting clips and screws, then remove the
luggage partition trim (A).
|
|
7. |
After loosening the mounting clips and screw, then remove the
rear wheel housing trim (A).
|
|
8. |
Disconnect the high mounted stop lamp connector (A).
|
|
9. |
Remove the rear seat belt upper anchor cover (A).
|
|
10. |
Remove the rear package tray trim (A).
|
|
11. |
Installation is the reverse of removal.
|
• |
Make sure the connectors are connected in properly.
|
|
• |
Replace any damage clips.
|
|
|
[5 Door, 4 Door]
1 . Front pillar trim
2 . Center pillar upper trim
3 . Center pillar lower trim
4 . Rear pillar trim [5 Door]
5 . Front door scuff trim
6 . ...
•
Put on gloves to protect your hands.
•
U ...
See also:
Cluster Ionizer (FATC only) Inspection
1.
Press the MODE switch more then 4 times within 2 seconds while
pressing the OFF switch.
Display
Fail description
00 ...
Front Hub / Knuckle Reassembly
1.
Install the hub bearing to the knuckle assembly.
(1)
Lay the knuckle assembly (A) on press.
(2)
...
Components
1. Parking brake lever
2. Adjuster cable
3. Equalizer assembly
4. Parking brake cable
...
Interior Trim Components
Trunk Trim Replacement