Kia Rio: Smart key unit Circuit diagram
| No. |
Connector A(26 pins) |
No. |
Connector B(16 pins) |
No. |
Connector C(22 pins) |
| 1 |
VBAT_LOAD |
1 |
C_CAN_L |
1 |
O_SSB_illumination_GND |
| 2 |
O_ESCL_GND |
2 |
C_CAN_H |
2 |
O_IMMO_IND |
| 3 |
Power_GND 1 |
3 |
- |
3 |
O_SSB_LED_OFF |
| 4 |
A_IGN1 |
4 |
L_Stop Lamp Fuse |
4 |
O_Interior_antenna #2_Power |
| 5 |
O_IGN1_Relay |
5 |
L_Brake switch |
5 |
O_Interior_antenna #1_Power |
| 6 |
A_ACC |
6 |
O_IMMO_antenna_power |
6 |
- |
| 7 |
A_IGN 2 |
7 |
O_ESCL_enable |
7 |
- |
| 8 |
L_SSB switch 2 |
8 |
F_Wheel speed |
8 |
O_Trunk_antenna_power/ O_Interior_antenna #3_Power |
| 9 |
- |
9 |
L_DRV toggle button |
9 |
O_Bumper_antenna_power/ O_Interior_antenna_Power |
| 10 |
- |
10 |
L_ESCL_unlock |
10 |
O_RH_side_antenna_power |
| 11 |
ESCL_COM |
11 |
O_exterior buzzer |
11 |
O_LH_side_antenna_power |
| 12 |
B_CAN_H |
12 |
L_P position/L_Clutch switch |
12 |
O_SSB_LED_BLUE/ O_SSB_LED_IGN |
| 13 |
B_CAN_L |
13 |
L_start feedback |
13 |
O_SSB_illumination_power |
| 14 |
VBAT_CPU |
14 |
O_IMMO_antenna_GND |
14 |
O_KEYOUT_IND |
| 15 |
O_ESCL_BAT |
15 |
DIAG-K |
15 |
O_interior_antenna#2_GND |
| 16 |
POWER_GND 2 |
16 |
O_SSB_LED_AMBER/ O_SSB_LED_ACC |
16 |
O_interior_antenna#1_GND |
| 17 |
O_Starter_Relay |
|
|
17 |
O_RESERVE2_antenna_GND O_RESERVE2/ L_RESERVE2 |
| 18 |
O_IGN2_Relay |
18 |
O_RESERVE1_antenna_GND |
||
| 19 |
O_ACC_Relay |
19 |
O_Trunk_antenna_GND/ O_Interior_antenna #3_GND |
||
| 20 |
- |
20 |
O_Bumper_antenna_GND/ O_Interior_antenna #3_GND |
||
| 21 |
L_Trunklid_Switch |
21 |
O_RH_side_antenna_GND |
||
| 22 |
- |
22 |
O_LH_side_antenna_GND |
||
| 23 |
F_RPM |
|
|
||
| 24 |
EMS_COM |
||||
| 25 |
L_SSB_Switch 1 |
||||
| 26 |
L_ASTtoggle button |
Smart key unit Inspection
Smart Key Unit
-
Refer to the BE group - inspection / self diagnosis with GDS.
Smart Key Switch
-
Refer to the BE group - inspection / self di ...
See also:
ESC Control Module Installation
1.
Installation is the reverse of removal.
2.
Tighten the HECU mounting bolts and nuts to the specified torque.
3.
...
Thermostat: Installation
1.
Place the thermostat in the block.
Install the thermostat (B) with the jiggle valve upward.
2.
Install the water inlet fitting (A).
...
Component Location
1. Driver power window main switch
2. Passenger power window switch
3. Front window motor
4. Rear window motor
5. Rear window switch
...
Copyright © www.kirmanual.com 2014-2024