Kia Rio Manuals

Kia Rio: Specifications - Engine Control / Fuel System - Kia Rio UB 2012-2024 Service ManualKia Rio: Specifications

Fuel Delivery System
Items
 Specification
Fuel Tank
 Capacity
 43 lit. (11.4 U.S.gal., 45.4 U.S.qt., 37.8 Imp.qt.)
Fuel Filter
 Type
 Paper type
Fuel Pressure
 Low Pressure Fuel Line
 480 ~ 520 kPa (4.89 ~ 5.30 kgf/cm², 69.6 ~ 75.4 psi)
High Pressure Fuel Line
 2.0 ~ 15.0 MPa (20.4 ~ 153.0 kgf/cm², 290.1 ~ 2175.6 psi)
Fuel Pump
 Type
 Electrical, in-tank type
Driven by
 Electric motor
High Pressure Fuel Pump
 Type
 Mechanical type
Driven by
 Camshaft

Sensors
Manifold Absolute Pressure Sensor (MAPS)
▷ Type: Piezo-resistive pressure sensor type
▷ Specification
Pressure
[kPa (kgf/cm², psi)]
 Output Voltage (V)
20.0 (0.20, 2.9)
 0.79
46.7 (0.47, 6.77)
 1.84
101.3 (1.03, 14.7)
 4.0

Intake Air Temperature Sensor (IATS)
▷ Type: Thermistor type
▷ Specification
Temperature
 Resistance (kΩ)
°C
 °F
-40
 -40
 40.93 ~ 48.35
-20
 -4
 13.89 ~ 16.03
0
 32
 5.38 ~ 6.09
10
 50
 3.48 ~ 3.90
20
 68
 2.31 ~ 2.57
40
 104
 1.08 ~ 1.21
50
 122
 1.56 ~ 1.74
60
 140
 0.54 ~ 0.62
80
 176
 0.29 ~ 0.34

Engine Coolant Temperature Sensor (ECTS)
▷ Type: Thermistor type
▷ Specification
Temperature
 Resistance (kΩ)
°C
 °F
-40
 -40
 48.14
-20
 -4
 14.13 ~ 16.83
0
 32
 5.79
20
 68
 2.31 ~ 2.59
40
 104
 1.15
60
 140
 0.59
80
 176
 0.32

Throttle Position Sensor (TPS) [integrated into ETC module]
▷ Type: Hall IC Non-contact sensor type
▷ Specification
Throttle angle(°)
 Output Voltage (V)
TPS1
 TPS2
0
 0.5
 4.5
10
 0.96
 4.05
20
 1.41
 3.59
30
 1.87
 3.14
40
 2.32
 2.68
50
 2.78
 2.23
60
 3.23
 1.77
70
 3.69
 1.32
80
 4.14
 0.86
90
 4.6
 0.41
98
 4.65
 0.35
C.T (0)
 0.5
 4.5
W.O.T (86)
 4.41
 0.59

Crankshaft Position Sensor (CKPS)
▷ Type: Magnetic field sensitive Type
▷ Specification
Item
 Specification
Coil Resistance (Ω)
 774 ~ 946 [20°C (68°F)]

Camshaft Position Sensor (CMPS)
▷ Type: Hall effect type
Knock Sensor (KS)
▷ Type: Piezo-electricity type
▷ Specification
Item
 Specification
Capacitance (pF)
 950 ~ 1,350
Resistance(MΩ)
 4.87

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 1]
▷ Type: Zirconia (ZrO2) [Linear] Type
▷ Specification
Item
 Specification
Heater Resistance (Ω)
 2.4 ~ 4.0 [20°C(69.8°F)]

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2]
▷ Type: Zirconia (ZrO2) [Binary] Type
▷ Specification
A/F Ratio (λ)
 Output Voltage(V)
RICH
 0.6 ~ 1.0
LEAN
 0 ~ 0.4

Item
 Specification
Heater Resistance (Ω)
 Approx. 9.0 [21°C(69.8°F)]

Rail Pressure Sensor (RPS)
▷ Type: Piezo-electricity type
▷ Specification


Accelerator Position Sensor (APS)
▷ Type: Variable resistor type
▷ Specification
Accelerator
Position
 Output Voltage (V)
APS1
 APS2
C.T
 0.7 ~ 0.8
 0.275 ~ 0.475
W.O.T
 3.8 ~ 4.4
 1.75 ~ 2.35

Fuel Tank Pressure Sensor (FTPS)
▷ Type: Piezo - Resistivity type
▷ Specification
Pressure
[kPa (kgf/cm², in H2O)
 Output Voltage (V)
-6.67 (-0.068, -26.8)
 0.5
0
 2.5
+6.67 (0.068, 26.8)
 4.5

Actuators
Injector
▷ Specification
Item
 Specification
Coil Resistance (Ω)
 1.5 [20°C(68°F)]

ETC Motor [integrated into ETC Module]
▷ Specification
Item
 Specification
Coil Resistance (Ω)
 0.3 ~ 100 [20°C(68°F)]

Purge Control Solenoid Valve (PCSV)
▷ Specification
Item
 Specification
Coil Resistance (Ω)
 22.0 ~ 26.0 [20°C(68°F)]

CVVT Oil Control Valve (OCV)
▷ Specification
Item
 Specification
Coil Resistance (Ω)
 6.9 ~ 7.9 [20°C(68°F)]

Variable Intake Solenoid (VIS) Valve
▷ Specification
Item
 Specification
Coil Resistance (Ω)
 30.0 ~ 35.0 [20°C(68°F)]

Fuel Pressure Regulator Valve
▷ Specification
Item
 Specification
Coil Resistance (Ω)
 0.5 [20°C(68°F)]

Ignition Coil
▷ Type: Stick type
▷ Specification
Item
 Specification
Primary Coil Resistance (Ω)
 0.75 ± 15％[20°C(68°F)]
Secendary Coil Resistance (kΩ)
 5.9 [20°C(68°F)]

Canister Close Valve (CCV)
▷ Specification
Item
 Specification
Coil Resistance (Ω)
 19.8 ~ 20.8 (20°C)

Engine Control / Fuel System
...

Service Standard
Item Specification Ignition Timing (°) BTDC 3 ± 10 Idle Speed (rpm) A/C OFF Neutral, N, P-range 630 ± 100 D-range ...

See also:

Rear Wiper Motor Inspection
Rear Wiper Motor 1. Remove the 4P connector from the rear wiper motor. 2. Connect battery positive (+) and negative (-) cables to terminals ...

Hands free switch Installation
1. Reassemble the hands free switch after connecting the connector. 2. Reassemble the steering wheel. 3. Reasse ...

Engine compartment
1. Engine Coolant Reservoir 2. Engine Oil Filler Cap 3. Brake/Clutch Fluid Reservoir 4. Air Cleaner 5. Fuse Box 6. Negative Battery Terminal 7. Positive Battery Terminal 8. Radiator Cap 9. E ...

Categories


Copyright © www.kirmanual.com 2014-2024