Kia Rio Manuals

Kia Rio: Installation - Parking Brake System - Brake System - Kia Rio UB 2012-2024 Service ManualKia Rio: Installation

Rear Disc Brake Type
1.
Install the parking brake cable.
2.
Install the parking brake cable (A), and then install the clip (B).
3.
Install the rear tire and wheel.
4.
Install the parking brake lever assembly.
Tightening torque:
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)


5.
Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.
Specified grease:
Multi purpose grease SAE J310, NLGI No.2


6.
Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).
Parking brake lever stroke:
5 ~ 7 clicks (Pull the lever with 196N (20 kgf, 44 lbf))

     
After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")



7.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
8.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
9.
Reconnect the connector (A) of parking brake switch.



     
Inspect the continuity of parking brake switch.
When the brake lever is pulled: continuity
When the brake lever is released: no continuity
10.
Install the floor console.
(Refer to Body group - "Floor console")
Rear Drum Brake Type
1.
Install the parking brake cable.
2.
Install the parking brake cable (A), and then install the clip (B).
3.
Remove the brake shoe.
(Refer to the rear drum brake)
4.
Install the rear tire and wheel.
5.
Install the parking brake lever assembly.


6.
Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.
Specified grease:
Multi purpose grease SAE J310, NLGI No.2


7.
Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).
Parking brake lever stroke:
5 ~ 7 clicks (Pull the lever with 196N (20 kgf, 44 lbf))

     
After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")



8.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
9.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
10.
Reconnect the connector (A) of parking brake switch.



     
Inspect the continuity of parking brake switch.
When the brake lever is pulled: continuity
When the brake lever is released: no continuity
11.
Install the floor console.
(Refer to Body group - "Floor console")
Removal
Rear Disc Brake Type    The parking brake cables must not be bent or distorted. This will lead to stiff operat ...

Adjustment
Parking Brake Lever Stroke Adjustment 1. Remove the floor console. (Refer to Body group - "Floor console") 2. Ap ...

See also:

Hood Adjustment
Hood Adjustment 1. After loosening the hinge (A) mounting bolt, adjust the hood (B) by moving it up or down, or right or left. 2. Adjus ...

Cruise Control
The cruise control system is engaged by the cruise "ON/OFF" main switch located on right of steering wheel column. The system has the capability to cruise, coast, accelerate and res ...

Blower Unit Components
1. Blower Motor 2. Blower Fan 3. Clamp 4. NVH Pad 5. Connection Case 6. Cluster Ionizer (FATC only) 7. Intake Case (Left) 8. Intake Seal 9. NVH Pad 10. Intake ...

Categories


Copyright © www.kirmanual.com 2014-2024