Kia Rio: Front Seat Belt Replacement
Front Seat Belt Replacement
| •
|
When installing the belt, make sure not to damaged the
pretensioner.
|
|
|
1. |
Remove the following items first :
| A. |
Front seat assembly
(Refer to the BD group - "Front Seat")
|
| B. |
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
|
|
|
2. |
Disconnect the battery negative cable, and wait for at least three
minutes before beginning work.
|
|
3. |
The seat belt anchor pretensioner (A) can be removed after pushing
the lock pin (B) as arrow direction.
|
|
4. |
Using a screwdriver or remover, remove the center pillar lower
trim (A).
|
|
5. |
Using a screwdriver or remover, remove the center pillar upper
trim (A).
|
|
6. |
After loosening the mounting bolt, then remove the front seat
belt upper anchor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
7. |
After disconnecting the pretensioner connector lock pin, remove
the seat belt pretensioner connector (A), loosen the mounting bolt,
then remove the pretensioner (B).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
8. |
Installation is the reverse of removal.
|
• |
Make sure the connector is plugged in properly.
|
|
• |
Replace any damage clips.
|
|
|
Height Adjust Replacement
|
1. |
Remove the following items first :
| A. |
Front seat assembly
(Refer to the BD group – “Front Seat”)
|
| B. |
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
|
| C. |
Front seat belt lower anchor
|
| D. |
Center pillar lower trim
(Refer to the BD group - "Interior Trim")
|
| E. |
Center pillar upper trim
(Refer to the BD group - "Interior Trim")
|
| F. |
Front seat belt upper anchor
|
|
|
2. |
After loosening the bolts, then remove the height adjustor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
3. |
Installation is the reverse of removal.
|
• |
Replace ant damaged clips.
|
|
• |
Make sure the height adjust properly.
|
|
|
Front Seat Belt Buckle Replacement
|
1. |
Remove the following items first :
| A. |
Front seat assembly
(Refer to the BD group - "Front Seat")
|
|
|
2. |
Remove the front seat belt buckle connector mounting clip (A).
|
|
3. |
After loosening the mounting bolt, then remove the front seat
belt buckle (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
|
4. |
Installation is the reverse of removal.
|
[Front]
(5 Door, 4 Door)
1. Front seat belt
2. Height adjust
3. Front seat belt anchor pretensioner (NA : North america)
[Rear]
...
Rear Seat Belt Replacement
[5 Door]
•
When installing the belt, make sure not ...
See also:
Thermostat: Components
1. Water inlet fitting
2. Thermostat
3. Heater pipe
4. Water temp control assembly
5. Water temperature sensor
6. Gasket
...
Front Door Adjustment
Glass Adjustment
•
Check the glass run channel for damage or deterioration,
and repl ...
Front Door Replacement
Front Door Trim Replacement
•
Take care not to scratch the door trim and other parts.
...
Components
Rear Seat Belt Replacement